SIZE GUIDE · October 08, 2026 · Sanzhu Engineering Team
Ordering the wrong O-ring size is one of the most common — and most avoidable — causes of seal failure. A ring that is slightly too large will not stay seated in its groove; one that is slightly too small gets overstretched, thins out, and loses sealing force. The good news is that every O-ring size in the world is defined by just two numbers. Learn to measure them correctly and you will get the right part the first time.
The two numbers that define every O-ring
An O-ring is a torus — a donut shape — and a donut is fully described by two dimensions. The inside diameter (ID) is the diameter of the hole through the middle. The cross-section (CS) is the thickness of the ring material itself. Everything else is derived from these two: outside diameter equals ID plus twice the CS. Suppliers, standards, and groove designs all speak in ID and CS, so these are the two numbers you need on every order.
How to measure an O-ring correctly
For a new, unused ring the job is straightforward. Measure the ID with calipers across the widest inside opening, then measure the CS at two or three points around the ring and average the readings. The critical rule: do not stretch the ring while measuring the ID. Even a small pull adds millimeters to the reading, and you will end up ordering a ring that is too big.
Used rings are trickier. Rubber takes a compression set over time, so a ring pulled from service may measure smaller in CS and larger in ID than when it was new. If the old ring is flattened or cracked, measure the groove it sat in instead — the groove width tells you the intended CS, and the groove diameter tells you the intended ID. When neither the ring nor the groove gives a clean reading, send us a photo of the old ring next to a ruler. We size rings from photos every week.
Reading AS568 dash numbers
Most inch-size O-rings follow AS568, the standard that assigns each size a dash number such as -214 or -325. The dash number tells you which of the five standard cross-sections the ring uses, and the exact ID within that series:
| Dash number range | Cross-section | Example | Example ID |
|---|---|---|---|
| -001 to -050 | 0.070 in (1.78 mm) | -006 | 0.114 in (2.90 mm) |
| -102 to -178 | 0.103 in (2.62 mm) | -112 | 0.487 in (12.37 mm) |
| -201 to -284 | 0.139 in (3.53 mm) | -214 | 0.984 in (25.00 mm) |
| -309 to -395 | 0.210 in (5.33 mm) | -325 | 1.475 in (37.47 mm) |
| -425 to -475 | 0.275 in (6.99 mm) | -425 | 4.475 in (113.67 mm) |
Once you know the dash number, any manufacturer in the world can supply the identical size — that interchangeability is the whole point of the standard.
Metric sizes and custom dimensions
Metric O-rings are usually specified directly as ID x CS, for example 25 x 3.55 mm — no dash number needed. ISO 3601 lists preferred metric sizes, but custom tooling covers everything else. If your size falls between standards, we can mold it: custom O-ring molds are routine work, and the tooling cost is often lower than buyers expect, especially when amortized over the order quantity.
Measuring tools: what to use
A decent pair of digital calipers covers most jobs — they read ID directly and measure CS to a hundredth of a millimeter. For large rings that will not sit flat in calipers, an O-ring measuring cone or a flexible measuring tape around the inside circumference works well; divide the circumference by pi to get the ID. Whatever tool you use, take each measurement twice and measure the CS at several points around the ring, since molded parts can vary slightly. And remember that rubber is temperature-sensitive: a ring measured in a cold warehouse will read a touch smaller than the same ring at room temperature, so let parts normalize before measuring when precision matters.
Three sizing mistakes to avoid
Measuring a stretched ring. Always let the ring relax to its natural shape first, and measure the ID without pulling.
Confusing ID with OD. Double-check which diameter your calipers are actually spanning — ordering by OD when the supplier expects ID guarantees the wrong part.
Ignoring the groove. The groove, not the ring alone, determines squeeze. A correctly sized ring in a worn or wrongly machined groove will still leak, so verify groove dimensions whenever a seal keeps failing.