PRODUCT GUIDE · October 09, 2026 · Sanzhu Engineering Team

A hydraulic cylinder looks simple from the outside, but inside it runs a small team of seals, each with exactly one job. Get the team wrong and the cylinder weeps oil, drifts under load, or scores its own rod. Here is what each member of the team does, which materials suit each role, and what information your supplier needs to get it right.

Rod seals: keeping the pressure in

The rod seal sits in the cylinder head and seals against the moving rod — the highest-duty dynamic seal in the assembly. Its job is to keep pressurized fluid inside the cylinder while the rod slides in and out thousands of times. Single-acting U-cups in polyurethane are the workhorse here: the lip shape uses system pressure to press harder as pressure rises. For high speeds, high temperatures, or aggressive fluids, PTFE cap seals with an elastomer energizer are the step up.

Piston seals: separating the chambers

The piston seal rides with the piston inside the bore and separates the pressure side from the return side of the cylinder. If it leaks internally, the cylinder drifts and loses holding force — a failure you feel as lost performance rather than a visible drip. Double-acting designs are common since most cylinders push and pull. Piston seals are almost always paired with wear rings (guide bands) that keep metal off metal; without them, side loads score the bore and no seal can survive.

Wipers: the first line of defense

The wiper — also called a scraper — sits outboard of the rod seal and its only job is to scrape dirt, moisture, and ice off the rod on every retract stroke. It is the cheapest part of the seal stack and the most underappreciated: a large share of premature rod-seal failures traces back to contamination that a proper wiper would have stopped. In dirty or outdoor environments, consider a double-lip wiper for extra protection.

Materials: matching compound to duty

Material choice follows the operating conditions, not habit. NBR covers general mineral-oil hydraulics at moderate temperatures. Polyurethane dominates dynamic rod and piston seals for its outstanding abrasion resistance. FKM handles high heat and aggressive synthetic fluids. PTFE offers the lowest friction for high-speed or dry-running spots. Temperature range and fluid type decide the shortlist; pressure and speed refine it.

What to tell your supplier

You do not need to design the seal stack yourself — but your supplier needs six facts to do it for you: rod and bore diameters, pressure range, rod speed, temperature range, fluid type, and whether the cylinder is single- or double-acting. With those six, an experienced seal engineer can recommend the full stack: wiper, rod seal, piston seal, wear rings, and static seals.

Common specification mistakes

Reusing the old seal's part number without checking the application. Cylinders get rebuilt, fluids get changed, pressures get turned up. A seal that worked for ten years can fail in ten days after any of those changes — re-validate the material against current conditions.

Skipping the wiper to save a few cents. The wiper is the cheapest seal in the stack and the one most often deleted from a rebuild kit. In dusty, wet, or outdoor service that saving is always false economy.

Ignoring the wear rings. A perfect piston seal cannot survive a piston that rocks metal-to-metal in the bore. If the old wear rings are worn through, the new seals will follow them — replace the guides with the seals, every time.

Mixing metric and inch hardware. Seal grooves are cut to one system or the other. Measure the groove, not just the old seal, before ordering — a 0.5 mm difference in groove width is enough to cause extrusion or nibbling.

Seal typeJobTypical materials
Rod sealKeeps pressure in around the moving rodPolyurethane, NBR, PTFE
Piston sealSeparates pressure and return chambersPolyurethane, NBR, PTFE + wear rings
Wiper / scraperCleans the rod, blocks contaminantsPolyurethane, NBR
Wear ringGuides piston and rod, prevents metal contactPTFE, phenolic, nylon
Static sealsSeal the head, cap and portsNBR, FKM O-rings

← Back to Blog  |  Send an Inquiry